Reactivity Insertion(반응성 삽입)란 무엇입니까?
Reactivity Insertion 반응성 삽입 - In SFR, the core configuration is not the most reactive during the nominal reactor operation, its geometry change or coolant voiding can induce a reactivity insertion. [1] The two models were coupled via a script that accounted for reactivity insertion between time steps and the changes caused in the fission power. [2] The restart of the CABRI reactor in 2015 offers the opportunity to validate tools involving multiphysic calculation schemes on reactivity insertions (RI) transients at a system scale. [3] The newly implemented models are tested on a transient initiated by a reactivity insertion of -50 pcm. [4] Rod Ejection Accidents are part of Reactivity Induced Accidents that induced through driven by reactivity insertion due to many failures. [5] The calculation results include value of reactivity insertion, change in power of reactor, as well as surface temperature of the hottest fuel assembly. [6] Three typical accidents are carried out in both ADS and CNES, including reactivity insertion, loss of flow, and loss of heat sink. [7] This magnitude of this parameter has safety implication, governing the rate at which power excursion results due to a reactivity insertion. [8] An understanding is therefore required of any implications for reactivity insertions during coolant pressure and temperature changes. [9] 50 worth of reactivity insertion with measured Full Widths at Half Maximum (FWHM) of 13. [10]SFR에서 노심 구성은 공칭 원자로 작동 중에 가장 반응성이 좋지 않으며, 형상 변경 또는 냉각재 보이드가 반응성 삽입을 유발할 수 있습니다. [1] 두 모델은 시간 단계 사이의 반응성 삽입과 핵분열력의 변화를 설명하는 스크립트를 통해 연결되었습니다. [2] 2015년 CABRI 원자로의 재가동은 시스템 규모에서 반응성 삽입(RI) 과도 현상에 대한 다중물리 계산 방식과 관련된 도구를 검증할 기회를 제공합니다. [3] 새로 구현된 모델은 -50 pcm의 반응성 삽입으로 시작된 과도 상태에서 테스트됩니다. [4] 막대 이탈 사고는 많은 고장으로 인한 반응성 삽입에 의해 유발된 반응성 유도 사고의 일부입니다. [5] 계산 결과에는 반응도 삽입 값, 원자로 출력의 변화, 가장 뜨거운 핵연료 집합체의 표면 온도가 포함됩니다. [6] 반응성 삽입, 흐름 손실 및 방열판 손실을 포함하여 ADS 및 CNES 모두에서 세 가지 일반적인 사고가 수행됩니다. [7] 이 매개변수의 크기는 반응성 삽입으로 인해 전력 이탈이 발생하는 비율을 제어하는 안전 관련성을 갖습니다. [8] 따라서 냉각수 압력 및 온도 변화 중 반응성 삽입에 대한 모든 의미에 대한 이해가 필요합니다. [9] 13의 FWHM(절반 최대 폭에서 전체 너비)으로 측정된 50분의 반응성 삽입. [10]
Positive Reactivity Insertion 양성 반응 삽입
This simple model is constructed to evaluate the design limit based on the relation between the allowable positive reactivity insertion rate defined by the core characteristics and that assumed by the effect of FCI phenomena. [1] The performance of the proposed framework is evaluated for load following scenarios with fast and slow ramp changes; along with accident handling with positive reactivity insertion tests. [2] For UTOP, the unexpected positive reactivity insertion of 0. [3] This results in positive reactivity insertion with reactor power increase of 0. [4] During certain accident conditions, the formation and the subsequent transportation towards the reactor core of a slug of coolant with reduced boron concentration can lead to a positive reactivity insertion. [5] The paper presents comparison of two methods for neutron pulse-mode detector non-linearity characterisation using VR-1 zero power reactor: (1) comparative method utilising the comparison of studied pulse-mode detection system with a response of gamma compensated ionisation chamber working in current mode, and (2) kinetics method utilising the asymptotic exponential power rise after positive reactivity insertion as a source of information on true signal. [6] The steam that enters the primary system would result in a positive reactivity insertion since steam is an excellent neutron moderator. [7] In particular, two cases of positive reactivity insertion were selected for detailed comparison, being the most relevant from the point of view of future practical applications. [8] Four instantaneous positive reactivity insertion case studies have been performed in the range of 2. [9]이 단순모형은 노심특성에 의해 정의된 허용가능한 양의 반응도 삽입율과 FCI 현상의 영향에 의해 가정되는 허용량 사이의 관계에 기초하여 설계한계를 평가하기 위해 구성된다. [1] 제안된 프레임워크의 성능은 램프 변경이 빠르고 느린 시나리오에 따른 부하에 대해 평가됩니다. 양성 반응 삽입 테스트를 통한 사고 처리와 함께. [2] UTOP의 경우 예상치 못한 양성 반응성 삽입이 0입니다. [3] 이는 원자로 전력 증가가 0인 양의 반응도 삽입을 초래합니다. [4] 특정 사고 조건에서 붕소 농도가 감소된 냉각제 슬러그의 형성 및 원자로 노심으로의 후속 운송은 양성 반응도 삽입으로 이어질 수 있습니다. [5] 이 논문은 VR-1 제로 파워 리액터를 사용하여 중성자 펄스 모드 검출기 비선형성 특성화를 위한 두 가지 방법의 비교를 제시합니다. 전류 모드 및 (2) 실제 신호에 대한 정보의 소스로 양의 반응성 삽입 후 점근 지수 전력 상승을 활용하는 동역학 방법. [6] 증기는 우수한 중성자 감속재이기 때문에 1차 시스템으로 들어가는 증기는 양성 반응도 삽입을 초래합니다. [7] 특히, 향후 실용화 측면에서 가장 관련성이 높은 2개의 양성반응도 삽입 사례를 선정하여 상세한 비교를 하였다. [8] 4개의 순시 양성 반응 삽입 사례 연구가 2의 범위에서 수행되었습니다. [9]
Negative Reactivity Insertion 음성 반응 삽입
The parameter does not exceed the critical point corresponding to the onset of the coolant boiling, and the coolant boiling does not occur because of the large negative reactivity insertion by the GEM. [1] The negative reactivity insertion was from 0. [2] Finally a transient, consisting of a negative reactivity insertion, is analyzed to assess the dynamic core behavior. [3] The consequent negative reactivity insertion by minor actinides was compensated by reducing the gadolinium content and boron concentration. [4]매개변수는 냉각수 비등의 시작에 해당하는 임계점을 넘지 않으며, GEM에 의한 음의 반응도 삽입이 크기 때문에 냉각수 비등은 발생하지 않는다. [1] 음성 반응성 삽입은 0부터였습니다. [2] 마지막으로 음성 반응 삽입으로 구성된 과도 현상을 분석하여 동적 코어 거동을 평가합니다. [3] 작은 악티늄족에 의한 결과적인 음성 반응성 삽입은 가돌리늄 함량과 붕소 농도를 감소시켜 보상되었습니다. [4]
reactivity insertion accident 반응성 삽입 사고
Other parameters such as reactivity insertion, power, and fuel temperature changes during the Reactivity Insertion Accident (RIA) simulation were evaluated as well. [1] And an analysis method was established to simulate the thermal–mechanical behavior of dispersed plate-type fuel under the Reactivity Insertion Accident (RIA). [2] For the purpose of reducing the volume and mass of the reactor, as well as ensuring the safety operation, it is necessary to determine the most effective reactivity control scheme, and analyze the corresponding reactivity insertion accidents. [3] Three different types of operation conditions are simulated with the control systems, including transients of normal load-follow operation, a reactivity insertion accident and a loss of flow accident. [4] Following a reactivity insertion accident, the power trend as a function of the time was also analyzed using the RELAP5/MOD3. [5] Development of accident tolerant fuel cladding gained importance after the Fukushima-Daiichi accident with the aim of preventing hydrogen embrittlement and uranium-zirconium eutectic formation in zirconium based claddings during accidental scenarios such as reactivity insertion accident (RIA) or loss of coolant accident (LOCA). [6] One dimensional space nuclear reactor system analysis code—SIMCODE is developed and five typical transient operation conditions are calculated, including the system startup, the loss of flow accident, the loss of heat sink accident, the reactivity insertion accident, and the small loss of coolant accident. [7] In this paper, based on the reactivity insertion accident (RIA) analysis, the fuel cladding damage has been analyzed for a 10 MWth LBE cooled fast reactor developed by Institute of Nuclear Energy Safety and Technology (INEST) using RELAP5. [8] Generation-IV sodium fast reactors (SFR) will only become acceptable and accepted if they can safely prevent or accommodate reactivity insertion accidents that could lead to the release of large quantities of mechanical energy, in excess of the reactor containment's capacity. [9] Two typical accidents for the FHR are simulated, including unprotected reactivity insertion accident (URIA) and unprotected overcooling (UOC) accident. [10] An advanced tube-burst test system was designed to test samples of nuclear fuel cladding under conditions relevant to a postulated design-basis reactivity insertion accident (RIA) in light-water reactors. [11]RIA(Reactivity Insertion Accident) 시뮬레이션 중 반응도 삽입, 출력 및 연료 온도 변화와 같은 기타 매개변수도 평가되었습니다. [1] 그리고 RIA(Reactivity Insertion Accident)에 따른 분산판형 핵연료의 열역학적 거동을 모사하기 위한 해석기법을 수립하였다. [2] 원자로의 부피와 질량을 줄이고 안전 운전을 보장하기 위해서는 가장 효과적인 원자로 제어 방안을 결정하고 해당 원자로 삽입 사고를 분석해야 합니다. [3] 정상 부하 추종 작동의 과도 상태, 반응도 삽입 사고 및 흐름 손실 사고를 포함하여 제어 시스템과 함께 세 가지 다른 유형의 작동 조건이 시뮬레이션됩니다. [4] 반응도 삽입 사고 이후 시간에 따른 전력 추세도 RELAP5/MOD3를 사용하여 분석했습니다. [5] 사고 내성 연료 피복재의 개발은 반응성 삽입 사고(RIA) 또는 냉각수 손실 사고(LOCA)와 같은 우발적 시나리오에서 지르코늄 기반 피복재의 수소 취성 및 우라늄-지르코늄 공정 형성을 방지하기 위한 목적으로 후쿠시마-다이치 사고 이후 중요하게 되었습니다. . [6] 1차원 공간 원자로 계통 해석 코드 - SIMCODE를 개발하여 계통 기동, 유량 손실 사고, 방열판 손실 사고, 반응도 삽입 사고, 냉각재 소실 등 5가지 일반적인 과도 운전 조건을 계산합니다. 사고. [7] 본 논문에서는 원자력안전기술원(INEST)이 개발한 10MWth LBE 냉각형 고속로 RELAP5를 이용하여 원자로 삽입사고(RIA) 분석을 기반으로 핵연료 피복관 손상을 분석하였다. [8] 4세대 나트륨 고속로(SFR)는 원자로 격납건물의 용량을 초과하여 대량의 기계적 에너지를 방출할 수 있는 원자로 삽입 사고를 안전하게 방지하거나 수용할 수 있는 경우에만 허용되고 수용될 것입니다. [9] FHR에 대한 두 가지 일반적인 사고는 비보호 반응도 삽입 사고(URIA) 및 비보호 과냉각(UOC) 사고를 포함하여 시뮬레이션됩니다. [10] 고급 튜브 파열 시험 시스템은 경수로에서 가정된 설계 기반 반응도 삽입 사고(RIA)와 관련된 조건에서 핵연료 피복재 샘플을 시험하도록 설계되었습니다. [11]
reactivity insertion effect
The temperature reactivity feedback effects of the fuel, TFE emitter, TFE collector, reflector, moderator and the reactivity insertion effects of control drums and safety drums are considered. [1] The temperature reactivity feedback effects of the fuel, TFE emitter, TFE collector, moderator, and reactivity insertion effects of the control drums and safety drums are considered. [2]연료, TFE 방출기, TFE 수집기, 반사기, 감속재의 온도 반응도 피드백 효과와 제어 드럼 및 안전 드럼의 반응도 삽입 효과를 고려합니다. [1] 연료, TFE 이미터, TFE 수집기, 감속재의 온도 반응도 피드백 효과와 제어 드럼 및 안전 드럼의 반응도 삽입 효과를 고려합니다. [2]
reactivity insertion case
To validate the proposed model, it is compared to the modified kinetics model in numerical calculations of two very simple reactivity insertion cases. [1] Four instantaneous positive reactivity insertion case studies have been performed in the range of 2. [2]제안된 모델을 검증하기 위해 두 가지 매우 간단한 반응성 삽입 사례의 수치 계산에서 수정된 동역학 모델과 비교됩니다. [1] 4개의 순시 양성 반응 삽입 사례 연구가 2의 범위에서 수행되었습니다. [2]
reactivity insertion rate 반응성 삽입율
This simple model is constructed to evaluate the design limit based on the relation between the allowable positive reactivity insertion rate defined by the core characteristics and that assumed by the effect of FCI phenomena. [1] Starting with simpler illustration of the concepts of neutron multiplication and the role of delayed neutrons in determining the rate of change of reactor power, the solutions to the kinetics equations for different types of reactivity insertion rate are discussed. [2]이 단순모형은 노심특성에 의해 정의된 허용가능한 양의 반응도 삽입율과 FCI 현상의 영향에 의해 가정되는 허용량 사이의 관계에 기초하여 설계한계를 평가하기 위해 구성된다. [1] 중성자 증배의 개념과 원자로 출력의 변화율을 결정하는 데 있어 지연 중성자의 역할에 대한 간단한 설명으로 시작하여 다양한 유형의 반응도 삽입율에 대한 동역학 방정식의 해가 논의됩니다. [2]