Membranes Modified(수정된 막)란 무엇입니까?
Membranes Modified 수정된 막 - Nafion117® membranes modified by three cationic cyclodextrin (CD) derivatives have been prepared by strong ionic bonding. [1] Comparing with membranes modified by a single MPEG or LA, the optimal composite membrane possesses excellent hydrophilicity(water contact angle of 0°), underwater hydrophobicity (underwater oil contact angle of 159°), and anti-fouling. [2] The physico-chemical properties and cytotoxicity of the membranes modified under various conditions were studied. [3] This paper discusses the synthesis, characterization and performance of polyethersulfone (PES) membranes modified with polyvinyl pyrrolidone (PVP) additives in order to improve the performance and antifouling properties of membranes. [4] Recently, graphene oxide (GO) based membranes modified with various chiral selectors had been proved to allow for both high permeation flux and enantioselectivity. [5] Membranes modified with zwitterionic brushes show a high potential for application in RED as they not only delay the onset of fouling but they also slow down the growth of the fouling layer, thus retaining higher power density outputs. [6] reaction temperature, solution concentration of TMC and organic additives) on the enantioseparation of membranes modified using interfacial polymerization method was then studied by using (DL)-tryptophan ((DL)-Trp) as model chiral drug. [7] The resultant membrane significantly enhanced biofouling resistance compared to the membranes modified by either the topological or chemical modifications alone due to the combinatorial antifouling effect. [8] The membranes modified by GO are able to adsorb the pharmacological substances, which was confirmed in the flow system. [9] Neutron studies of the channels for molecular and ionic transports in membranes modified with different nanoparticles were carried out. [10] A significant reduction of oil fouling for membranes modified by plasma treatment was confirmed. [11] The membranes modified by the methods proposed in this study did not lose their hydrophobicity and maintained the flux over a significantly longer period. [12] In addition, base membranes and membranes modified by grafting 1-vinyl-3-allylimidazolium bromide were challenged with produced water that was pretreated by electrocoagulation. [13] The membranes modified with a longer main chain of pMEDSAH and a long side chain of pPEG had good resistance against both the bacterial adhesion and dynamic biofouling. [14] It is in this light that polyvinylidene fluoride/polytetrafluoroethylene (PVDF/PTFE) membranes modified with methyl functionalized silica nanoparticles (MfSNPs) were fabricated to produce microporous hydrophobic composite membranes for water recovery from urine. [15] It was found that membranes modified with positive charges were more prone to molasses fouling, where the effect of the membrane surface properties on fouling was significant only above the threshold flux. [16] In this work, dense and supported pervaporation polyvinyl alcohol (PVA)-based membranes modified with poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate)(PSS)/PAH top nanolayers were synthesized. [17] When challenged with PW, membranes modified with polvinylallyl imidazolium bromide chains provided the greatest resistance to fouling. [18] The results indicated that the membranes modified with larger ZIF-8 particles (80–100 nm) showed higher permeability and flux recovery ratio (FRR %) than those with smaller particles (60–70 nm). [19] This study evaluates the properties of chitosan (CS) membranes modified with different percentages (0. [20] Base NF 270 nanofiltration membranes as well as membranes modified by grafting poly(N-isopropylacrylamide) chains from the membrane surface using atom transfer radical polymerization were investigated. [21] Hydrophilic polyvinylidene difluoride (PVDF) and polysulfone (PSF) membranes modified by hydrophilic additives such as polyvinylpyrrolidone (PVP) are widely used in various industrial fields. [22]3개의 양이온성 사이클로덱스트린(CD) 유도체로 변형된 Nafion117® 멤브레인은 강력한 이온 결합에 의해 제조되었습니다. [1] 단일 MPEG 또는 LA로 개질된 멤브레인에 비해 최적의 복합 멤브레인은 우수한 친수성(수중 접촉각 0°), 수중 소수성(수중 오일 접촉각 159°) 및 방오성을 가지고 있습니다. [2] 다양한 조건에서 변형된 막의 물리화학적 특성과 세포독성을 연구하였다. [3] 이 문서에서는 막의 성능과 방오 특성을 개선하기 위해 폴리비닐 피롤리돈(PVP) 첨가제로 개질된 폴리에테르설폰(PES) 막의 합성, 특성화 및 성능에 대해 논의합니다. [4] 최근에 다양한 키랄 선택자로 변형된 산화 그래핀(GO) 기반 멤브레인이 높은 투과 플럭스와 거울상 선택성을 모두 허용하는 것으로 입증되었습니다. [5] 양쪽성 이온 브러시로 수정된 멤브레인은 오염의 시작을 지연시킬 뿐만 아니라 오염층의 성장을 늦추어 더 높은 전력 밀도 출력을 유지하기 때문에 RED에 적용할 가능성이 높습니다. [6] 반응 온도, TMC 및 유기 첨가제의 용액 농도) 계면 중합법을 사용하여 변형된 막의 거울상 분리에 대한 (DL)-트립토판((DL)-Trp)을 모델 키랄 약물로 사용하여 연구했습니다. [7] 생성된 막은 조합 방오 효과로 인해 토폴로지 또는 화학적 변형만으로 개질된 막과 비교하여 생물학적 오염 저항성이 크게 향상되었습니다. [8] GO로 개질된 멤브레인은 약리물질을 흡착할 수 있으며, 이는 유동계에서 확인되었다. [9] 상이한 나노입자로 변형된 막에서 분자 및 이온 수송을 위한 채널에 대한 중성자 연구가 수행되었다. [10] 플라즈마 처리로 개질된 멤브레인에 대한 오일 오염의 상당한 감소가 확인되었습니다. [11] 이 연구에서 제안한 방법으로 수정된 멤브레인은 소수성을 잃지 않고 상당히 오랜 기간 동안 플럭스를 유지했습니다. [12] 또한 1-vinyl-3-allylimidazolium bromide를 접목하여 변형된 기저막과 막에 전기응고법으로 전처리한 생성수를 챌린지했습니다. [13] 더 긴 pMEDSAH 주쇄와 pPEG의 긴 측쇄로 변형된 막은 박테리아 부착과 동적 생물학적 오염 모두에 대해 우수한 저항성을 보였습니다. [14] 이러한 관점에서 메틸 작용성 실리카 나노입자(MfSNP)로 개질된 폴리비닐리덴 플루오라이드/폴리테트라플루오로에틸렌(PVDF/PTFE) 멤브레인을 제작하여 소변에서 수분 회수를 위한 미세 다공성 소수성 복합 멤브레인을 제조했습니다. [15] 양전하로 개질된 막은 당밀 오염에 더 취약한 것으로 밝혀졌으며, 오염에 대한 막 표면 특성의 영향은 임계 플럭스 이상에서만 유의했습니다. [16] 이 작업에서 폴리(알릴아민 염산염)(PAH) 및 폴리(나트륨 4-스티렌설포네이트)(PSS)/PAH 상부 나노층으로 변형된 조밀하고 지지된 투과증발 폴리비닐 알코올(PVA) 기반 멤브레인이 합성되었습니다. [17] PW로 시험을 했을 때, polvinylallyl imidazolium bromide 사슬로 변형된 멤브레인은 오염에 대한 가장 큰 저항성을 제공했습니다. [18] 결과는 더 큰 ZIF-8 입자(80-100nm)로 개질된 멤브레인이 더 작은 입자(60-70nm)를 가진 것보다 더 높은 투과성과 자속 회복율(FRR %)을 나타냄을 나타냅니다. [19] 이 연구는 다른 비율로 변형된 키토산(CS) 막의 특성을 평가합니다(0. [20] 기본 NF 270 나노여과막과 원자이동 라디칼 중합을 사용하여 막 표면에서 폴리(N-이소프로필아크릴아미드) 사슬을 그래프트하여 개질된 막을 조사했습니다. [21] 친수성 폴리비닐리덴 디플루오라이드(PVDF) 및 폴리설폰(PSF) 멤브레인은 폴리비닐피롤리돈(PVP)과 같은 친수성 첨가제로 개질되어 다양한 산업 분야에서 널리 사용됩니다. [22]
Etched Membranes Modified
To address this, systematic filtration experiments are performed in this work using the EpCAM+ cell line MCF-7 as CTC-model and standard track-etched membranes modified with or without antibodies against EpCAM. [1] The aim of the research is to study the possibility of using track-etched membrane, including track-etched membranes modified with cold plasma, followed by layering prenatal stem cells (PSC) on the material surface in surgical treatment of bullous keratopathy (BK). [2] The aim of the research is to study the possibility of using track-etched membrane, including track-etched membranes modified with cold plasma, followed by layering prenatal stem cells (PSC) on the material surface in surgical treatment of bullous keratopathy (BK). [3]이 문제를 해결하기 위해 EpCAM+ 세포주 MCF-7을 CTC 모델로 사용하고 EpCAM에 대한 항체가 있거나 없이 수정된 표준 트랙 에칭 멤브레인을 사용하여 체계적인 여과 실험을 수행합니다. [1] 이 연구의 목적은 수포성 각막병증(BK)의 외과적 치료에서 저온 플라즈마로 변형된 트랙 에칭 멤브레인을 포함하여 트랙 에칭 멤브레인을 재료 표면에 적층한 후 산전 줄기 세포(PSC)를 사용할 가능성을 연구하는 것입니다. [2] 이 연구의 목적은 수포성 각막병증(BK)의 외과적 치료에서 저온 플라즈마로 변형된 트랙 에칭 멤브레인을 포함하여 트랙 에칭 멤브레인을 재료 표면에 적층한 후 산전 줄기 세포(PSC)를 사용할 가능성을 연구하는 것입니다. [3]
Exchange Membranes Modified 수정된 교환막
The possibility of adequate theoretical estimation of the limiting diffusion current for ion-exchange membranes modified by organic and inorganic dopants is shown. [1] Ion-exchange membranes modified with fullerenol and oxidized graphene maintain high proton conductivity at elevated temperatures and low humidity. [2] A number of one-layer perfluorinated cation-exchange membranes modified by halloysite clay nanotubes were prepared using two different solvents: dimethylformamide and isopropanol. [3]유기 및 무기 도펀트로 변형된 이온 교환막에 대한 제한 확산 전류에 대한 적절한 이론적 추정의 가능성이 표시됩니다. [1] 풀러레놀과 산화 그래핀으로 변형된 이온 교환막은 높은 온도와 낮은 습도에서 높은 양성자 전도도를 유지합니다. [2] 할로이사이트 점토 나노튜브로 개질된 다수의 1층 퍼플루오르화 양이온 교환막이 디메틸포름아미드와 이소프로판올의 두 가지 다른 용매를 사용하여 제조되었습니다. [3]
Hybrid Membranes Modified
This article lucidly explains the fabrication of novel PVA-based hybrid membranes modified with cationic and anionic layers. [1] In this work, PA hybrid membranes modified with oxidized graphitic carbon nitride (CNO), graphitic carbon nitride (g-C3N4), or graphene oxide (GO) are prepared by interfacial polymerization. [2]이 기사는 양이온 및 음이온 층으로 변형된 새로운 PVA 기반 하이브리드 멤브레인의 제조를 명확하게 설명합니다. [1] 이 연구에서 산화된 흑연질화탄소(CNO), 흑연질화탄소(g-C3N4) 또는 산화그래핀(GO)으로 개질된 PA 하이브리드 멤브레인은 계면 중합에 의해 준비됩니다. [2]
Nanofibrou Membranes Modified
In this work, the silk fibroin/cellulose blend nanofibrous membranes modified with sodium-3-sulfobenzoate (S-SCBNM) were fabricated by electrospinning technique for lysozyme adsorption. [1] In this work, we fabricate the silk-derived nanofibrous membranes modified with 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BDSNM) that could yield reactive oxygen species (ROS) driven under UV light irradiation. [2]이 연구에서, 소듐-3-설포벤조에이트(S-SCBNM)로 변형된 실크 피브로인/셀룰로오스 블렌드 나노섬유 멤브레인은 리소자임 흡착을 위한 전기방사 기술에 의해 제작되었습니다. [1] 이 작업에서 우리는 UV 광 조사 하에서 구동되는 활성 산소 종(ROS)을 생성할 수 있는 3,3',4,4'-벤조페논 테트라카르복실산 이무수물(BDSNM)로 변형된 실크 유래 나노섬유 막을 제작합니다. [2]
Nanofiber Membranes Modified
The present work describes a unique modification process for electrospun polyacrylonitrile (PAN) nanofiber membranes modified with β-cyclodextrin (β-CD) monomers and their application in the adsorption of bromophenol blue and atrazine from aqueous systems. [1] Cellulose acetate nanofiber membranes modified with both polyvinylpyrrolidone (PVP) coated cellulose nanocrystals (CNC@PVP) and pristine CNCs were prepared using the reinforcement concentration varying from 0 to 0. [2]본 연구는 β-시클로덱스트린(β-CD) 단량체로 변형된 전기방사된 폴리아크릴로니트릴(PAN) 나노섬유 막에 대한 독특한 변형 과정과 수성 시스템에서 브로모페놀 블루 및 아트라진의 흡착에 대한 적용을 설명합니다. [1] 폴리비닐피롤리돈(PVP) 코팅된 셀룰로오스 나노결정(CNC@PVP)과 깨끗한 CNC로 변형된 셀룰로오스 아세테이트 나노섬유 멤브레인은 0에서 0까지 다양한 강화 농도를 사용하여 준비되었습니다. [2]
Ceramic Membranes Modified 세라믹 멤브레인 수정
Novel ceramic membranes modified with MWCNT are characterized by 45. [1] During the experiments, ceramic membranes modified with titanium and completed in a filtering element were used. [2]MWCNT로 변형된 새로운 세라믹 멤브레인은 45개의 특징이 있습니다. [1] 실험 동안 티타늄으로 개질되고 여과 요소로 완성된 세라믹 멤브레인이 사용되었습니다. [2]