Heat Resistant Stainless(내열성 스테인리스)란 무엇입니까?
Heat Resistant Stainless 내열성 스테인리스 - 01C ferritic heat-resistant stainless steel was investigated at temperatures ranging from 973 to 1123 K and stresses from 15 to 90 MPa. [1] The grinding experiments were performed on structural alloy steel 30KhGSN2/30KhGSNA, structural carbon steel AISI 1045, corrosion-resistant and heat-resistant stainless steel AISI 321, and heat-resistant nickel alloy KHN77TYuR. [2] 1Cr11Ni2W2MoV is a new martensitic heat-resistant stainless steel utilized in the manufacturing of aero-engine high-temperature bearing components. [3] X10CrAlSi18 FHSS (ferritic heat-resistant stainless steel) has received a lot of attention due to its advantageous combination of creep resistance and oxidation resistance. [4] A previous work has shown that a modified HP-NbTi heat-resistant stainless steel exhibited a different magnetic behavior after 90,000 hours of operation in a steam reformer furnace exposed to temperatures between 500 °C and 550 °C or between 950 °C and 1000 °C. [5] In this study, the homemade heat-resistant stainless steel fluidized bed was designed and constructed as a vertical, circular cross-section column for conducting the thermal ALD process. [6] 6 wt% was prepared on heat-resistant stainless steel via an intermittent ultrasonic-assisted electroless plating method. [7] The effect of Al content on the microstructure and ductile-brittle transition temperature (DBTT) of 18Cr–Al–Si ferritic heat-resistant stainless steel have been studied by Charpy impact testing over temperatures ranging from 20 to 90 ℃. [8] Using scanning electron microscopy (SEM), EDS and OM methods, the microstructures and phase compositions of the reaction layers formed by the corrosion of the ZL101 melt in the four iron-based stirring paddles of A3 steel, heat-resistant stainless steel 1. [9] The effect of Al content on the high-temperature oxidation (800 and 900 °C) of 18Cr–Al–Si FHSS (ferritic heat-resistant stainless steel) for up to 180 h in air was investigated via the isothermal oxidation method. [10] A comparative study of the high-temperature oxidation behavior and mechanism of 0Cr25Ni20 austenitic heat-resistant stainless steel (AHSS) and 0Cr18AlSi ferritic heat-resistant stainless steel (FHSS) at 800°C, 900°C, and 1000°C in air up to 140 h was performed using isothermal oxidation tests. [11]01C 페라이트 내열 스테인리스강은 973~1123K 범위의 온도와 15~90MPa의 응력에서 조사되었습니다. [1] 연삭 실험은 구조용 합금강 30KhGSN2/30KhGSNA, 구조용 탄소강 AISI 1045, 내식성 및 내열 스테인리스강 AISI 321, 내열 니켈 합금 KHN77TYuR에 대해 수행되었습니다. [2] 1Cr11Ni2W2MoV는 항공기 엔진 고온 베어링 부품 제조에 사용되는 새로운 마르텐사이트 내열 스테인리스강입니다. [3] X10CrAlSi18 FHSS(페라이트계 내열성 스테인리스강)는 내크리프성과 내산화성의 유리한 조합으로 인해 많은 관심을 받았습니다. [4] 이전 연구에서는 수정된 HP-NbTi 내열 스테인리스강이 500°C ~ 550°C 또는 950°C ~ 1000°C 사이의 온도에 노출된 증기 개질로에서 90,000시간 작동 후 다른 자기 거동을 나타냄을 보여주었습니다. 씨. [5] 본 연구에서는 열 ALD 공정을 수행하기 위한 수직 원형 단면 기둥으로 수제 내열 스테인리스강 유동층을 설계 및 시공하였다. [6] 6wt%는 간헐적 초음파 보조 무전해 도금 방법을 통해 내열 스테인리스강에 준비되었습니다. [7] 18Cr-Al-Si 페라이트계 내열 스테인리스강의 미세구조와 연성-취성 전이 온도(DBTT)에 대한 Al 함량의 영향은 20~90℃ 범위의 온도에 대한 샤르피 충격 시험에 의해 연구되었습니다. [8] 주사 전자 현미경(SEM), EDS 및 OM 방법을 사용하여 ZL101의 부식에 의해 형성된 반응층의 미세 구조 및 상 조성이 A3강, 내열 스테인리스강 1의 철 기반 교반 패들 4개에서 녹습니다. [9] 공기 중에서 최대 180시간 동안 18Cr-Al-Si FHSS(페라이트계 내열성 스테인리스강)의 고온 산화(800 및 900°C)에 대한 Al 함량의 영향을 등온 산화 방법을 통해 조사했습니다. [10] nan [11]