Catalytic Membranes(촉매막)란 무엇입니까?
Catalytic Membranes 촉매막 - The use of catalytic membranes in chemical reactor engineering has significantly improved the reactor performance. [1] This paper reviews recent progress in the photocatalytic membranes for wastewater treatment and water purification with an emphasis on the type of membranes, membrane fabrication, and applications in pollutant removal. [2] This study reviews the application of carbon nitride in gas separation membranes, pervaporation membranes, nanofiltration membranes, reverse osmosis membranes, ion exchange membranes and catalytic membranes, along with describing the separation mechanisms. [3] The performance of the UiO-66-NH2 and ZIF-8 biocatalytic membranes in a gas-liquid membrane contactor showed formic acid yields of 13% (3. [4] Catalytic membranes as heterogeneous reactors are appealing for treating persistent pollutants. [5] Much attention was paid to the study of catalytic membranes in order to overcome this issue, since it is convenient for catalytic membranes to be employed in devices for practical applications. [6] The elimination of dye pollutants from wastewater is a significant concern that has prompted extensive research into the development of highly efficient photocatalytic membranes. [7] Photocatalytic membranes were fabricated via vacuum assisted layer-by-layer (LBL) self-assembly of 0D-2D Bi2MoO6-g-C3N4 on a PDA coated thin-film composite PVDF substrate by Schiff base reaction. [8] The attained results revealed that catalytic membranes can be an efficient alternative for the removal dissolved organic matter and membrane fouling mitigation during water treatment. [9] Thus, this chapter aims to approach the main aspects of oily wastewater treatment by catalytic membranes, including enzymatic and advanced oxidation processes, as photocatalysis, electrocatalysis, and Fenton-like processes. [10] Photocatalytic membranes have received increasing attention due to their excellent separation and photodegradation of organic contaminants in wastewater. [11] Photocatalytic membranes (PMs), in which photocatalyst nanoparticles are deposited or immobilized to enhance their performance, can provide a complete treatment of wastewater due to the dual action over pollutants: retention/rejection/repulsion and photodegradation. [12] The tremendous performance of photocatalytic membranes is attributed to the photogenerated reactive oxygen species such as hydroxyl radicals, singlet oxygen, and superoxide anion radicals introduced by catalytic nanoparticles such as TiO2 and ZnO upon light irradiation. [13] Catalytic membranes can simultaneously realize physical separation and chemical oxidation in one integrated system, which is the frontier technology for effective removal of organic containments in wastewater treatment. [14] The catalytic membranes were assembled in a tube-in-tube configuration and tested over 6 h of continuous nitrobenzene hydrogenation with molecular hydrogen. [15] Performance evaluation, challenges, and future directions regarding the utilization of electrospun nanofibrous photocatalytic membranes in wastewater treatment are comprehensively reviewed. [16] Biocatalytic membranes (BCMs), in which enzymes are immobilized on membranes, combines the advantages of membrane separation and enzymatic degradation. [17] Herein, we utilized a facile strategy to construct novel 3D sea urchin-like nitrogen doped carbon nanotube (CNT) frameworks encapsulated Co nanoparticles (ZIF-67/CNTs) through N-molecule assisted pyrolysis of ZIF-67, and then immobilized on poly(vinylidene fluoride) (PVDF) membrane to obtain the catalytic membranes (ZIF-67/[email protected]). [18] While such photocatalytic membranes have demonstrated that they can recover their inherent permeability, less information is known about the effect of photocatalysis on the kinetics of the permeate flux. [19] This study will aid the development of carbon-based catalytic membranes for water treatment. [20] Thereby, it showed that the La-TiO2 photocatalytic membranes were successfully fabricated with antifouling, self-cleaning properties. [21] Therefore, the surface modification of a nylon membrane with TiO2(B) and rGO can serve as a promising route to fabricate photocatalytic membranes for use in the water treatment industry. [22] Studies have delivered significant scientific findings and described promising features such as visible light activation, floating photocatalytic reactors, photocatalytic membranes, and multiple functionality for insitu remediation under solar radiation, ultimately. [23] The emergence of hybrid photocatalytic membranes has provided a new direction in search of efficient technologies to separate and degrade pollutants present in wastewaters. [24] Therefore, this aims at critically assessing the properties of electrocatalytic membranes used in ECMR, mechanisms involved in degradation of organic pollutants and optimal parameters to carry out electrocatalytic reactions, which helps in identifying and bridging the research gaps for the large scale employment of ECMRs in wastewater remediation. [25] The research therefore represents an advance in the application of biocatalytic membranes as technological alternative for juice debittering. [26] To palliate to such limitations, we embedded binary nanoparticles in polymer fibers to design photocatalytic membranes. [27] Photocatalytic membrane reactors are those in which photocatalytic membranes are used for degradation of pollutants and then separate the photocatalysts and products present in the wastewater. [28] This article provides an in-depth review on the roles of both photocatalysis and membrane technology in hybrid photocatalytic membranes for the treatment of POP containing wastewaters. [29] Overall, the results achieved in this work may provide promising insights into enzyme immobilization on polymeric supports for the development of high-efficiency biocatalytic membranes for CO2 capture in GLMC applications. [30] HydrophiLic surface modifying macromolecules (LSMM) modified polyethersulfone (PES) based photocatalytic membranes have been successfully prepared. [31] Finally, current technological challenges and potential solutions concerning the industrial implementation of such photocatalytic membranes are discussed. [32] Scanning electron microscopy (SEM) analysis revealed that the photocatalytic membranes had a porous sublayer, a compact top layer, and that, some of the nanoparticles were not encapsulated by the membranes. [33] Application of photocatalytic membranes has emerged as a very promising technique to solve this problem. [34] Current research focused on a radical solution for actual application in which the PVDF-TiO2 hollow fiber photocatalytic membranes were fabricated to simultaneously separate and degrade the surfactants laden in produced water. [35] The stabilization of catalytic membranes was greatly improved when the crosslinking temperature reached 120°C, and the conversion remained at 76% with the membrane soaked in ethanol solution about 24 h. [36] These biocatalytic membranes were tested in a solid-gas BMR and compared in terms of enzyme specific activity, catalytic activity and volumetric reaction rate. [37] To evaluate antifouling performance of photocatalytic membranes, we conducted a four-stage filtration system, and the flux recovery ratio (FRR) of MCU-C3N4/PVDF membranes reached over 80% (optimum 91%) under visible light irradiating (λ > 420 nm) for 30 min. [38] In this review, we discussed the recent developments of catalytic membranes from two aspects: preparation of catalytic membrane and its application in gas cleaning. [39] Apart from offering a novel strategy to prepare GO-based biocatalytic membranes for micropollutant removal and detection, this work further clarifies the interaction mechanism between GO, laccase and micropollutants, especially in a polymeric membrane matrix. [40] 1 wt%) in the catalytic membranes, the decolorizations of 327 ppm (1 mM) and 1635 ppm (5 mM) MO in water were complete within 2 and 8 min, respectively. [41] The micro-structures and compositions of the catalytic membranes were investigated by a number of advanced characterisations. [42] Blending photocatalytic membranes (BPMs) are favored materials for wastewater treatment due to their photocatalytic activity, high permeability and fouling resistance. [43] TiO2 embedded poly (vinylidene fluoride) (PVDF)/PMMA photocatalytic membranes were prepared by phase inversion method. [44] Recently, photocatalytic membranes are used to purify drinking water and have shown a great potential in efficient for water and wastewater treatment. [45] Photocatalytic membranes (PMs), coupling of membrane filtration and photocatalysis in a single unit, have exhibited a great potential for use in energy-efficient water purification and wastewater treatment. [46] Therefore, this study provides a promising methodology for the successful fabrication of high-performance membrane through the integration of photo-Fenton and membrane process, and further proposes a new strategy on the design and application of functional materials for new generation of catalytic membranes. [47] In the HPMR system, even though the RB5 photocatalytic degradation exhibits lower efficiency however the rejection of RB5 was achieved up to 95% under UV irradiation due to the properties of photocatalytic membranes. [48] Finally, in HA filtration tests, Ce-ZrO2 photocatalytic membranes were able to recover the flux in a fouled membrane using visible-light by degrading HA. [49] Photocatalytic membranes (PMs), coupling of membrane filtration and photocatalysis, have exhibited the potential for application in the wastewater treatment. [50]화학 반응기 엔지니어링에서 촉매 막을 사용하면 반응기 성능이 크게 향상되었습니다. [1] 이 논문은 막의 유형, 막 제조 및 오염 물질 제거 응용에 중점을 두고 폐수 처리 및 정수를 위한 광촉매 막의 최근 진행 상황을 검토합니다. [2] 이 연구는 분리 메커니즘을 설명함과 함께 가스 분리막, 투과증발막, 나노여과막, 역삼투막, 이온 교환막 및 촉매막에 탄소질화물의 적용을 검토합니다. [3] 기체-액체 막 접촉기에서 UiO-66-NH2 및 ZIF-8 생촉매 막의 성능은 13%의 포름산 수율을 보여주었다(3. [4] 불균일 반응기로서의 촉매막은 잔류성 오염물질을 처리하는 데 매력적입니다. [5] 이러한 문제를 극복하기 위해 촉매막 연구에 많은 관심을 기울였다. 촉매막은 실용화 장치에 사용하는 것이 편리하기 때문이다. [6] 폐수에서 염료 오염 물질을 제거하는 것은 고효율 광촉매 멤브레인 개발에 대한 광범위한 연구를 촉발한 중요한 문제입니다. [7] 광촉매 멤브레인은 Schiff 염기 반응에 의해 PDA 코팅된 박막 복합 PVDF 기판에서 0D-2D Bi2MoO6-g-C3N4의 진공 보조 층별(LBL) 자가 조립을 통해 제작되었습니다. [8] 달성된 결과는 촉매막이 수처리 동안 용해된 유기물 제거 및 막 오염 완화를 위한 효율적인 대안이 될 수 있음을 보여주었습니다. [9] 따라서 이 장에서는 광촉매, 전기촉매 및 Fenton 유사 공정과 같은 효소 및 고급 산화 공정을 포함하여 촉매막에 의한 유성 폐수 처리의 주요 측면에 접근하는 것을 목표로 합니다. [10] 광촉매 멤브레인은 폐수에서 유기 오염 물질의 우수한 분리 및 광분해로 인해 점점 더 주목을 받고 있습니다. [11] 광촉매 나노 입자가 증착되거나 고정되어 성능을 향상시키는 광촉매 멤브레인(PM)은 오염 물질에 대한 이중 작용(저류/거부/반발 및 광분해)으로 인해 폐수를 완벽하게 처리할 수 있습니다. [12] 광촉매 멤브레인의 엄청난 성능은 빛을 조사할 때 TiO2 및 ZnO와 같은 촉매 나노 입자에 의해 도입된 하이드록실 라디칼, 일중항 산소 및 슈퍼옥사이드 음이온 라디칼과 같은 광 생성된 활성 산소 종에 기인합니다. [13] 촉매막은 하나의 통합 시스템에서 물리적 분리와 화학적 산화를 동시에 실현할 수 있으며, 이는 폐수 처리에서 유기물 오염물질을 효과적으로 제거하기 위한 최첨단 기술입니다. [14] 촉매 멤브레인은 튜브 내 튜브 구성으로 조립되었고 분자 수소를 사용한 연속 니트로벤젠 수소화의 6시간에 걸쳐 테스트되었습니다. [15] 전기방사 나노섬유 광촉매막을 폐수 처리에 활용하는 것과 관련된 성능 평가, 과제 및 향후 방향을 종합적으로 검토합니다. [16] 효소가 막에 고정된 생촉매 막(BCM)은 막 분리와 효소 분해의 장점을 결합합니다. [17] 여기에서, 우리는 ZIF-67의 N-분자 보조 열분해를 통해 캡슐화된 Co 나노입자(ZIF-67/CNT)를 캡슐화한 새로운 3D 성게와 유사한 질소 도핑된 탄소 나노튜브(CNT) 프레임워크를 구성한 다음 폴리( 비닐리덴 플루오라이드)(PVDF) 멤브레인을 사용하여 촉매 멤브레인(ZIF-67/[email protected])을 얻습니다. [18] 이러한 광촉매 멤브레인은 고유한 투과성을 회복할 수 있음을 입증했지만 투과 플럭스의 동역학에 대한 광촉매 효과에 대한 정보는 덜 알려져 있습니다. [19] 이 연구는 수처리용 탄소 기반 촉매막 개발에 도움이 될 것입니다. [20] 이로써, La-TiO2 광촉매 막이 방오성, 자가 세정 특성을 갖고 성공적으로 제조되었음을 보여주었다. [21] 따라서 TiO2(B)와 rGO로 나일론 막의 표면 개질은 수처리 산업에서 사용하기 위한 광촉매 막을 제조하는 유망한 경로로 작용할 수 있습니다. [22] 연구는 가시광선 활성화, 부유 광촉매 반응기, 광촉매 멤브레인 및 궁극적으로 태양 복사 아래의 현장 복원을 위한 다중 기능과 같은 유망한 기능을 설명하고 중요한 과학적 발견을 제공했습니다. [23] 하이브리드 광촉매 멤브레인의 출현은 폐수에 존재하는 오염 물질을 분리하고 분해하는 효율적인 기술을 찾는 새로운 방향을 제시했습니다. [24] 따라서 이것은 ECMR에 사용되는 전기 촉매막의 특성, 유기 오염 물질의 분해와 관련된 메커니즘 및 전기 촉매 반응을 수행하기 위한 최적의 매개변수를 비판적으로 평가하는 것을 목표로 합니다. 교정. [25] 따라서 이 연구는 주스 짠맛을 제거하기 위한 기술적 대안으로서 생체촉매 멤브레인 적용의 발전을 나타냅니다. [26] 이러한 한계를 완화하기 위해 고분자 섬유에 이원 나노 입자를 내장하여 광촉매 막을 설계했습니다. [27] 광촉매 분리막 반응기는 광촉매 분리막을 이용하여 오염물질을 분해한 후 폐수에 존재하는 광촉매와 생성물을 분리하는 반응기이다. [28] 이 기사는 POP 함유 폐수 처리를 위한 하이브리드 광촉매 멤브레인에서 광촉매와 멤브레인 기술의 역할에 대한 심층 검토를 제공합니다. [29] 전반적으로, 이 작업에서 얻은 결과는 GLMC 응용 분야에서 CO2 포집을 위한 고효율 생체 촉매막 개발을 위한 고분자 지지체에 대한 효소 고정화에 대한 유망한 통찰력을 제공할 수 있습니다. [30] 친수성 표면 변형 거대분자(LSMM) 변형 폴리에테르설폰(PES) 기반 광촉매 멤브레인이 성공적으로 준비되었습니다. [31] 마지막으로, 이러한 광촉매 멤브레인의 산업적 구현과 관련된 현재의 기술적 과제와 잠재적 솔루션에 대해 논의합니다. [32] 주사전자현미경(SEM) 분석은 광촉매 막이 다공성 하부층, 조밀한 상부층을 갖고 일부 나노입자가 막으로 캡슐화되지 않은 것으로 밝혀졌다. [33] 이러한 문제를 해결하기 위한 매우 유망한 기술로 광촉매막의 적용이 대두되고 있다. [34] 현재 연구는 PVDF-TiO2 중공사 광촉매 막을 제조하여 생산수에 포함된 계면활성제를 동시에 분리 및 분해하는 실제 응용을 위한 라디칼 솔루션에 중점을 둡니다. [35] 촉매막의 안정화는 가교 온도가 120°C에 도달했을 때 크게 개선되었으며, 막을 에탄올 용액에 약 24시간 담가두었을 때 전환율은 76%로 유지되었다. [36] 이러한 생촉매 멤브레인은 고체 기체 BMR에서 테스트되었으며 효소 비활성, 촉매 활성 및 부피 반응 속도 측면에서 비교되었습니다. [37] 광촉매 멤브레인의 방오 성능을 평가하기 위해 4단계 여과 시스템을 수행했으며 MCU-C3N4/PVDF 멤브레인의 FRR(플럭스 회수율)은 가시광선 조사(λ>420nm)에서 80% 이상(최적 91%)에 도달했습니다. ) 30분 동안 [38] 이 리뷰에서 우리는 촉매막의 준비와 가스 세정에서의 응용이라는 두 가지 측면에서 촉매막의 최근 발전에 대해 논의했습니다. [39] 미세 오염 물질 제거 및 검출을 위해 GO 기반 생체 촉매 막을 준비하는 새로운 전략을 제공하는 것 외에도 이 연구는 특히 고분자 막 매트릭스에서 GO, 락카제 및 미세 오염 물질 사이의 상호 작용 메커니즘을 더욱 명확하게 합니다. [40] 촉매막에서 327ppm(1mM)과 1635ppm(5mM) MO의 탈색은 각각 2분과 8분 이내에 완료되었다. [41] 촉매막의 미세 구조와 조성은 여러 가지 고급 특성 분석을 통해 조사되었습니다. [42] 혼합 광촉매 멤브레인(BPM)은 광촉매 활성, 높은 투과성 및 내오염성으로 인해 폐수 처리에 선호되는 재료입니다. [43] TiO2 매립된 폴리(비닐리덴 플루오라이드)(PVDF)/PMMA 광촉매 멤브레인은 위상 반전 방법으로 제조되었습니다. [44] 최근 광촉매막은 음용수를 정화하는 데 사용되며 물 및 폐수 처리에 대한 효율성이 큰 잠재력을 보여주고 있습니다. [45] 광촉매 멤브레인(PM)은 멤브레인 여과와 광촉매를 단일 장치로 결합하여 에너지 효율적인 정수 및 폐수 처리에 사용할 수 있는 큰 잠재력을 보여주었습니다. [46] 따라서 본 연구는 포토펜톤과 멤브레인 공정의 통합을 통한 고성능 멤브레인의 성공적인 제조를 위한 유망한 방법론을 제공하고, 나아가 차세대 촉매 멤브레인을 위한 기능성 재료의 설계 및 적용에 대한 새로운 전략을 제안합니다. [47] HPMR 시스템에서는 RB5 광촉매 분해 효율이 낮음에도 불구하고 광촉매 멤브레인의 특성으로 인해 UV 조사에서 RB5 거부율이 최대 95%까지 달성되었습니다. [48] 마지막으로 HA 여과 테스트에서 Ce-ZrO2 광촉매 막은 HA를 분해하여 가시광선을 사용하여 오염된 막의 플럭스를 회복할 수 있었습니다. [49] 막 여과와 광촉매의 결합인 광촉매 막(PM)은 폐수 처리에 적용할 가능성을 보여주었습니다. [50]
Performance Catalytic Membranes 성능 촉매 멤브레인
Despite recent advances, there still exists considerable challenges in developing high performance catalytic membranes. [1] This study provides new insights into the design of high-performance catalytic membranes for efficient removal of micropollutants together with high water permeability, which makes it an attractive choice for membrane development in real scale applications. [2] This strategy provides guidance to the design of high-performance catalytic membranes. [3]최근의 발전에도 불구하고 고성능 촉매막을 개발하는 데에는 여전히 상당한 과제가 존재합니다. [1] 이 연구는 높은 투수성과 함께 미세 오염 물질의 효율적인 제거를 위한 고성능 촉매 멤브레인의 설계에 대한 새로운 통찰력을 제공하므로 실제 규모 응용 분야에서 멤브레인 개발에 매력적인 선택이 됩니다. [2] 이 전략은 고성능 촉매막 설계에 대한 지침을 제공합니다. [3]
Novel Catalytic Membranes
In this paper, novel catalytic membranes mats were fabricated through a one-pot synthesis from ammonium tetrathiomolybdate (ATTM) doped poly(acrylonitrile) (PAN) nanofibers for sub-micron diameter aerosol particle removal. [1] Nonprecious bimetallic molybdenum and iron embedded into N-doped carbon (MoFe-NC) hybrids were designed and fabricated by pyrolysis of mixed precursors and then immobilized on poly (vinylidene fluoride) (PVDF) films via a phase inversion process to obtain novel catalytic membranes ([email protected]) for toxic CrVI reduction. [2]이 논문에서, 새로운 촉매 멤브레인 매트는 서브마이크론 직경의 에어로졸 입자 제거를 위해 암모늄 테트라티오몰리브데이트(ATTM) 도핑된 폴리(아크릴로니트릴)(PAN) 나노섬유로부터 원 포트 합성을 통해 제작되었습니다. [1] N-도핑된 탄소(MoFe-NC) 하이브리드에 포함된 비귀금속 바이메탈 몰리브덴과 철은 혼합 전구체의 열분해에 의해 설계 및 제작된 다음 상 반전 공정을 통해 폴리(비닐리덴 플루오라이드)(PVDF) 필름에 고정화되어 새로운 촉매 멤브레인을 얻습니다. [email protected]) 독성 CrVI 감소. [2]
Nanostructured Catalytic Membranes 나노구조 촉매막
Though the nanostructured catalytic membranes, Nano sorbents and nanophotocatalyst are the established methods to eliminate water pollutants from wastewater, they need more energy and additional investment. [1] Nanostructured catalytic membranes and nano-photocatalysts are efficient and eco-friendly tools for the removal of contaminants from wastewater and antimicrobial activities, but they require more research and investment. [2]나노구조 촉매막, 나노 흡착제 및 나노광촉매는 폐수에서 수질 오염물질을 제거하기 위해 확립된 방법이지만 더 많은 에너지와 추가 투자가 필요합니다. [1] 나노구조의 촉매막과 나노광촉매는 폐수 및 항균 활성에서 오염물질을 제거하기 위한 효율적이고 친환경적인 도구이지만 더 많은 연구와 투자가 필요합니다. [2]
catalytic membranes provide 촉매막 제공
In short, the construction of catalytic membranes provides a new idea for wastewater treatment. [1] Due to the synergistically enhanced efficiency and self-cleaning performance, photocatalytic membranes provide an energy sustainable and environment friendly approach for water purification. [2]요컨대, 촉매막의 구성은 폐수 처리에 대한 새로운 아이디어를 제공합니다. [1] 시너지 효과로 향상된 효율성과 자체 세척 성능으로 인해 광촉매 멤브레인은 지속 가능한 에너지와 수질 정화를 위한 환경 친화적인 접근 방식을 제공합니다. [2]