Boiling Heat
끓는 열

Sentence Examples

Discover more insights into Boiling Heat 끓는 열

Keywords frequently search together with Boiling Heat 끓는 열

Narrow sentence examples with built-in keyword filters

Boiling Heat sentence examples within critical heat flux

critical heat flux
임계 열유속

These saturated pool boiling experiments and the visualizations verify that the present two-phase immersion cooling can enhance both the boiling heat transfer and the critical heat flux of water and FC-72.

이러한 포화 풀 비등 실험과 시각화는 현재의 2상 침지 냉각이 비등 열 전달과 물과 FC-72의 임계 열유속을 모두 향상시킬 수 있음을 확인합니다.

Enhancement of the critical heat flux of saturated pool boiling by the breathing phenomenon induced by lotus copper in combination with a grooved heat transfer surface

critical heat flux
임계 열유속

As a result, the NaCl solution presents a lower nucleate boiling heat flux than that of water when the imposed superheat is smaller than a critical superheat, while it exhibits a larger heat flux even a higher critical heat flux than water when the superheat is higher than the critical superheat.

그 결과, NaCl 용액은 부과된 과열도가 임계 과열도보다 작을 때 물보다 핵비등 열유속이 낮고, 과열도가 임계 과열도.

Numerical study of bubble behaviors and heat transfer in pool boiling of water/NaCl solutions using the lattice Boltzmann method

More critical heat flux sentences
임계 열유속 More Sentences

Boiling Heat sentence examples within two phase flow

two phase flow
2상 흐름

The flow pattern is of great significance for calculating boiling heat transfer and two phase flow pressure drop, and there is no uniform flow pattern diagram for the evaporative cooling system.

유동 패턴은 비등 열 전달 및 2상 유동 압력 강하를 계산하는 데 매우 중요하며 증발 냉각 시스템에 대한 균일한 유동 패턴 다이어그램이 없습니다.

Visual Experimental Study on Two Phase Flow Patterns of the Evaporative Cooling System

two phase flow
2상 흐름

The two-phase flow boiling heat transfer technique is widely believed to address the heating problem posed by HPC racks.

2상 유동 비등 열 전달 기술은 HPC 랙에서 발생하는 가열 문제를 해결하는 것으로 널리 알려져 있습니다.

Experimental Characterization of Two-Phase Cold Plates Intended for High-Density Data Center Servers Using a Dielectric Fluid

More two phase flow sentences
2상 흐름 More Sentences

Boiling Heat sentence examples within heat transfer coefficient

heat transfer coefficient
열전달 계수

This paper presents an experimental analysis on flow boiling heat transfer and pressure drop characteristics in a plate heat exchanger, and the development of prediction methods for the heat transfer coefficient and frictional pressure drop.

본 논문에서는 판형 열교환기의 유동 비등 열전달 및 압력 강하 특성에 대한 실험적 분석과 열전달 계수 및 마찰 압력 강하에 대한 예측 방법의 개발을 제시한다.

Experimental analysis of high temperature flow boiling heat transfer and pressure drop in a plate heat exchanger

heat transfer coefficient
열전달 계수

Also, the traditional convection heat transfer coefficient is compared with the boiling heat transfer coefficient in terms of how they influence the fluid and rock heat transfer model.

또한 기존의 대류 열전달 계수는 유체 및 암석 열전달 모델에 미치는 영향 측면에서 끓는 열전달 계수와 비교됩니다.

Impact of boiling heat transfer on geothermal reservoir simulation using local thermal non-equilibrium model

More heat transfer coefficient sentences
열전달 계수 More Sentences

Boiling Heat sentence examples within frictional pressure drop

frictional pressure drop
마찰 압력 강하

The objective of this study is to establish generalized correlations for R32 flow boiling heat transfer and frictional pressure drop in horizontal channels with wide ranges of geometric and flow parameters.

이 연구의 목적은 광범위한 기하학적 및 유동 매개변수를 사용하여 수평 채널에서 R32 유동 비등 열 전달 및 마찰 압력 강하에 대한 일반화된 상관 관계를 설정하는 것입니다.

New generalized flow boiling heat transfer and frictional pressure drop correlations for R32

frictional pressure drop
마찰 압력 강하

An experiment was carried out to study the effect of refrigerant mass flow rate, heat flux density, and saturation temperature on boiling heat transfer coefficient and frictional pressure drop in m.

냉매의 질량유량, 열유속밀도, 포화온도가 끓는 열전달계수와 마찰압력강하(m)에 미치는 영향을 알아보기 위해 실험을 수행하였다.

Experimental Research on Flow and Heat Transfer in Microchannel with Refrigerant HFO1234yf

More frictional pressure drop sentences
마찰 압력 강하 More Sentences

Boiling Heat sentence examples within study experimentally investigated

study experimentally investigated
실험적으로 조사한 연구

This study experimentally investigated the influence of heterogeneous wettability-patterned surfaces with varying inter-spacing on flow boiling heat transfer characteristics.

이 연구는 유동 비등 열전달 특성에 대한 다양한 간격을 갖는 이질적 습윤성 패턴 표면의 영향을 실험적으로 조사했습니다.

Enhancement of flow boiling heat transfer using heterogeneous wettability patterned surfaces with varying inter-spacing

study experimentally investigated
실험적으로 조사한 연구

This study experimentally investigated pool boiling heat transfer on copper tubes for superhydrophilic surfaces with square patterns of different wettability levels.

이 연구는 다양한 습윤성 수준의 정사각형 패턴을 갖는 초친수성 표면에 대한 구리 튜브의 풀 비등 열 전달을 실험적으로 조사했습니다.

Effects of difference in wettability level of biphilic patterns on copper tubes in pool boiling heat transfer

More study experimentally investigated sentences
실험적으로 조사한 연구 More Sentences

Boiling Heat sentence examples within heat transfer performance

heat transfer performance
열전달 성능

It was found that nucleate boiling heat transfer induced by rough surface increased the heat transfer performance in the case of the sandblasted plate.

거친 표면에 의해 유도된 핵비등 열전달은 샌드블라스트된 판의 경우 열전달 성능을 증가시키는 것으로 밝혀졌다.

Thermo-fluid dynamic analysis in a micro-textured evaporator based on microscale infrared/visible observations for loop heat pipes

heat transfer performance
열전달 성능

Higher heat flux increases the rate of bubble formation and promotes nucleate-boiling heat transfer, but it also intensifies the film boiling, thereby degrading the heat-transfer performance.

열유속이 높을수록 기포 형성 속도가 증가하고 핵 비등 열 전달이 촉진되지만 필름 비등도 심화되어 열 전달 성능이 저하됩니다.

Heat-transfer characteristics of CO2 boiling flow in the regenerative cooling channel of an Mg/CO2 powder rocket engine for Mars missions

More heat transfer performance sentences
열전달 성능 More Sentences

Boiling Heat sentence examples within high heat flux

high heat flux

Subcooled flow boiling heat transfer is one of the most preferred heat removal methods, especially in areas where high heat fluxes are encountered.

과냉각 흐름 비등 열 전달은 특히 높은 열 유속이 발생하는 영역에서 가장 선호되는 열 제거 방법 중 하나입니다.

On the prediction of pressure drop in subcooled flow boiling of water

high heat flux

ABSTRACT The boiling heat transfer characteristics of R134a in a helically coiled tube under high heat flux condition were investigated experimentally in present paper.

초록 본 논문에서는 높은 열유속 조건에서 나선형으로 감긴 관에서 R134a의 비등 열전달 특성을 실험적으로 조사하였다.

Flow Boiling Heat Transfer of R134a in a Vertical Helically Coiled Tube

More high heat flux sentences
More Sentences

Boiling Heat sentence examples within artificial neural network

artificial neural network

In this study, pool boiling heat flux was estimated in the isolated bubble regime using two optimization methods (genetic and artificial bee colony algorithm) and three machine learning algorithms (decision tree, artificial neural network, and support vector machine).

이 연구에서는 두 가지 최적화 방법(유전 및 인공 꿀벌 군집 알고리즘)과 세 가지 기계 학습 알고리즘(결정 트리, 인공 신경망 및 지원 벡터 머신)을 사용하여 고립된 거품 영역에서 풀 끓는 열유속을 추정했습니다.

Heat Flux Estimation at Pool Boiling Processes with Computational Intelligence Methods

artificial neural network

In the present research, an artificial neural network model was developed to predict the pool boiling heat transfer coefficient (HTC) of refrigerant-based nanofluids based on a large number of experimental data (1342) extracted from the literature.

본 연구에서는 문헌에서 추출한 수많은 실험 데이터(1342)를 기반으로 냉매 기반 나노유체의 풀 비등 열전달 계수(HTC)를 예측하기 위한 인공 신경망 모델을 개발했습니다.

Prediction of pool boiling heat transfer coefficient for various nano-refrigerants utilizing artificial neural networks

More artificial neural network sentences
More Sentences

Boiling Heat sentence examples within mass flow rate

mass flow rate

In this study, film boiling heat transfers of liquid hydrogen flowing inside of heated pipe were measured under saturated conditions at the absolute pressures of 700 kPa for various mass flow rates.

본 연구에서는 다양한 질량유량에 대해 절대압력 700kPa, 포화상태에서 가열관 내부를 흐르는 액체수소의 막비등 열전달을 측정하였다.

Film boiling heat transfer properties of liquid hydrogen flowing inside of heated pipe

mass flow rate

Ultimately the ultrafast water permeation property of the cured GNPs enhances the efficiency of nucleate pool boiling, leading to a maximum enhancement of 151% in the boiling heat transfer coefficient and 154% in the vapor mass flow rate.

궁극적으로 경화된 GNP의 초고속 투수 특성은 핵 풀 비등의 효율성을 향상시켜 비등 열전달 계수에서 최대 151% 및 증기 질량 유량에서 154%의 최대 향상을 가져옵니다.

Nucleate pool boiling enhancement by ultrafast water permeation in graphene-nanostructure

More mass flow rate sentences
More Sentences

Boiling Heat sentence examples within phase heat transfer

phase heat transfer

This paper reports the improved two-phase heat transfer characteristics at vertical micro-nano hybrid surfaces and demonstrates the effects of surface characteristics in micro- and nano-scale on two-phase heat transfer, which provide a new insight on effectively enhancing boiling heat transfer.

이 논문은 수직 마이크로-나노 하이브리드 표면에서 개선된 2상 열전달 특성을 보고하고 2상 열전달에 대한 마이크로 및 나노 규모의 표면 특성 효과를 보여줌으로써 비등 열 전달을 효과적으로 향상시키는 새로운 통찰력을 제공합니다. .

Study on microbubble dynamic behaviors at vertical micro-nano hybrid surfaces based on open capillary microgrooves heat sink

phase heat transfer

While the presence of the jet does not enhance the boiling heat transfer coefficient, the jet does greatly increase single-phase heat transfer performance and extends the critical heat flux limit.

제트의 존재는 끓는 열 전달 계수를 향상시키지 않지만 제트는 단상 열 전달 성능을 크게 증가시키고 임계 열유속 한계를 확장합니다.

Identification of Nucleate Boiling as the Dominant Heat Transfer Mechanism during Confined Two-Phase Jet Impingement

More phase heat transfer sentences
More Sentences

Boiling Heat sentence examples within kg m−2 s−1

kg m−2 s−1

The flow boiling heat transfer coefficients are measured for mass velocity ranging between 150 and 800 kg m−2 s−1, for heat fluxes from 12 to 60 kW m−2, at a saturation temperature at the inlet of the test section of 20°C.

유동 비등 열 전달 계수는 20°의 테스트 섹션 입구의 포화 온도에서 150~800kg m-2 s-1 범위의 질량 속도, 12 ~ 60kW m-2 범위의 열유속에 대해 측정됩니다. 씨.

R513A flow boiling heat transfer inside horizontal smooth tube and microfin tube

More kg m−2 s−1 sentences
More Sentences

Boiling Heat sentence examples within starting vapor quality

starting vapor quality

Experimental results show that: the increase of heat flux has significant effect on enhancing nucleate boiling heat transfer, while it's can also speed up the dryout process and decrease the starting vapor quality of dryout; the effect of mass flow rate on heat transfer coefficient is slight but as mass flow rate increasing, the starting vapor quality of dryout decreases, and the heat transfer coefficient increases after the dryout happens; the effect of saturation temperature on the physical properties of CO2 is the main cause of the different heat transfer characteristics in different experimental conditions, with the increasing of saturation temperature, the starting vapor quality of dryout has a decline tendency and the heat transfer coefficient has a steeper fall after dryout happens.

실험 결과는 다음을 보여줍니다. 열유속의 증가는 핵 비등 열 전달을 향상시키는 데 상당한 영향을 미치는 반면 건조 과정을 가속화하고 건조의 시작 증기 품질을 감소시킬 수 있습니다. 열전달 계수에 대한 질량 유량의 영향은 미미하지만 질량 유량이 증가함에 따라 건조의 시작 증기 품질이 감소하고 건조가 발생한 후 열전달 계수가 증가합니다. CO2의 물리적 특성에 대한 포화 온도의 영향은 다른 실험 조건에서 다른 열 전달 특성의 주요 원인이며, 포화 온도가 증가함에 따라 건조의 시작 증기 품질은 감소하는 경향이 있고 열 전달 계수는 건조가 발생한 후 더 가파르게 떨어집니다.

Investigation of flow boiling heat transfer characteristics of CO2in horizontal mini-tube

More starting vapor quality sentences
More Sentences

Boiling Heat sentence examples within Flow Boiling Heat

Flow Boiling Heat
흐름 끓는 열

In contrast to pool boiling, flow boiling heat transfer is a more applied mode of heat transfer and has been most widely used in high heat flux cooling systems.

풀 비등과 달리 유동 비등 열 전달은 열 전달에 더 많이 적용되는 모드이며 높은 열유속 냉각 시스템에서 가장 널리 사용되었습니다.

Review on high heat flux flow boiling of refrigerants and water for electronics cooling

Flow Boiling Heat
흐름 끓는 열

The groove-wall microchannel possesses high performance for flow boiling heat transfer.

홈 벽 마이크로 채널은 유동 비등 열 전달에 대한 고성능을 가지고 있습니다.

An experimental investigation of flow boiling characteristics in silicon-based groove-wall microchannels with different structural parameters

More Flow Boiling Heat sentences
흐름 끓는 열 More Sentences

Boiling Heat sentence examples within Pool Boiling Heat

Pool Boiling Heat
수영장 끓는 열

In the present study, the nucleate pool boiling heat transfer characteristics of water on the hydrophilic and uncoated metal foam covers were experimentally investigated, and were compared with those on hydrophobic metal foam covers to analyze the influence of surface wettability on pool boiling heat transfer on metal foam covers.

본 연구에서는 친수성 및 코팅되지 않은 금속폼 커버에 대한 물의 핵 풀 비등 열전달 특성을 실험적으로 조사하고, 소수성 금속폼 커버와 비교하여 표면 습윤성이 풀 비등 열전달에 미치는 영향을 분석하였다. 거품 덮개.

Influence of surface wettability on pool boiling heat transfer on metal foam covers

Pool Boiling Heat
수영장 끓는 열

In the present study, bubble growth on the boiling surfaces and pool boiling heat transfer characteristics of semi-modified pillar arrays are experimentally investigated at atmospheric pressure, while the bubble behaviors inside pillar gaps are numerically revealed in different contact angles by lattice Boltzmann method based on the pseudopotential LB model.

본 연구에서는 대기압에서 비등면의 기포 성장과 반개질 기둥 어레이의 풀 비등 열전달 특성을 실험적으로 조사하였으며, 기둥 간극 내부의 기포 거동은 유사전위 LB 모델.

Experimental and numerical investigation on bubble behaviors and pool boiling heat transfer of semi-modified copper square pillar arrays

More Pool Boiling Heat sentences
수영장 끓는 열 More Sentences

Boiling Heat sentence examples within Nucleate Boiling Heat

Nucleate Boiling Heat
핵 끓는 열

We have used Direct Numerical Simulations to study the effect of base plate oscillations on nucleate boiling heat transfer at low super heat in the isolated bubble regime.

우리는 격리된 기포 영역에서 낮은 과열도에서 핵 비등 열 전달에 대한 베이스 플레이트 진동의 영향을 연구하기 위해 직접 수치 시뮬레이션을 사용했습니다.

Dual grid level set method based direct numerical simulations of nucleate boiling with oscillating base plate

Nucleate Boiling Heat
핵 끓는 열

By comparing the boiling inception time and evaporation rate of liquid argon atoms, it is found that the ring-patterned surface shows an advantage in the nucleate boiling heat transfer compared with the stripe-patterned one.

액체 아르곤 원자의 끓는 시작 시간과 증발 속도를 비교하여 링 패턴 표면이 스트라이프 패턴 표면에 비해 핵 비등 열 전달에서 이점을 나타냄을 알 수 있습니다.

Study of Boiling Heat Transfer on Heterogeneous Wetting Surface With MD Simulation

More Nucleate Boiling Heat sentences
핵 끓는 열 More Sentences

Boiling Heat sentence examples within Subcooled Boiling Heat

Subcooled Boiling Heat
과냉각 끓는 열

The working modes of the ultra-thin flat-plate heat pipe under different heat loads include evaporation heat transfer, subcooled boiling heat transfer, nucleated boiling heat transfer and the drying zone beyond the heat transfer limit.

다양한 열 부하 하에서의 초박형 평판 히트 파이프의 작동 모드에는 증발 열 전달, 과냉각 비등 열 전달, 핵 생성 비등 열 전달 및 열 전달 한계를 넘어선 건조 영역이 포함됩니다.

Visualization study on boiling heat transfer of ultra-thin flat heat pipe with single layer wire mesh wick

Subcooled Boiling Heat
과냉각 끓는 열

Aside from demonstrating this potential, an assessment of available subcooled boiling heat transfer coefficient correlations identified Moles and Shaw's to predict the new experimental data with an overall mean absolute error of only 11.

이러한 가능성을 보여주는 것 외에도 사용 가능한 과냉각 비등 열 전달 계수 상관 관계의 평가는 Moles와 Shaw's를 식별하여 전체 평균 절대 오차가 11에 불과한 새로운 실험 데이터를 예측했습니다.

Experimental investigation of subcooled flow boiling in annuli with reference to thermal management of ultra-fast electric vehicle charging cables

More Subcooled Boiling Heat sentences
과냉각 끓는 열 More Sentences

Boiling Heat sentence examples within Film Boiling Heat

Film Boiling Heat
필름 끓는 열

In order to investigate the liquid-vapour interface behavior and film boiling heat transfer of FeCrAl, experiments are carried out with FeCrAl.

FeCrAl의 액체-증기 계면 거동과 막 비등 열 전달을 조사하기 위해 FeCrAl을 사용하여 실험을 수행했습니다.

Experimental investigation on the transient film boiling heat transfer during quenching of FeCrAl

Film Boiling Heat
필름 끓는 열

A scale analysis has been performed to investigate the film boiling heat transfer associated with cooling of a horizontal flat plate through water jet impinging.

물 분사 충돌을 통한 수평 평판의 냉각과 관련된 필름 비등 열 전달을 조사하기 위해 규모 분석이 수행되었습니다.

Scale analysis for water jet impingement over a horizontal flat plate under film boiling configuration

More Film Boiling Heat sentences
필름 끓는 열 More Sentences

Boiling Heat sentence examples within Phase Boiling Heat

Phase Boiling Heat

Two-phase boiling heat transfer performance, pressure drop and two-phase flow instabilities of the ORPFM were systematically explored.

ORPFM의 2상 비등 열전달 성능, 압력 강하 및 2상 유동 불안정성을 체계적으로 조사했습니다.

Experimental study of flow boiling performance of open-ring pin fin microchannels

Phase Boiling Heat

The two-phase boiling heat transport system exhibits oscillations and flow instabilities in varying scales in operating and accident conditions and they influence the thermal and reactivity margins in design.

2상 비등 열전달 시스템은 작동 및 사고 조건의 다양한 규모에서 진동 및 유동 불안정성을 나타내며 설계의 열 및 반응성 마진에 영향을 미칩니다.

Experimental Measurement and Analysis of Natural Circulation Flow Oscillations in a Vertically Heated Channel

More Phase Boiling Heat sentences
More Sentences

Boiling Heat sentence examples within Enhancing Boiling Heat

Enhancing Boiling Heat

Enhancing boiling heat transfer by surface modification has the potential to increase the efficiency of energy systems and to address thermal management bottlenecks in electronics.

표면 개질을 통해 끓는 열 전달을 향상시키면 에너지 시스템의 효율성을 높이고 전자 장치의 열 관리 병목 현상을 해결할 수 있습니다.

Composite porous surfaces of microcavities for enhancing boiling heat transfer

Enhancing Boiling Heat

This paper reports the improved two-phase heat transfer characteristics at vertical micro-nano hybrid surfaces and demonstrates the effects of surface characteristics in micro- and nano-scale on two-phase heat transfer, which provide a new insight on effectively enhancing boiling heat transfer.

이 논문은 수직 마이크로-나노 하이브리드 표면에서 개선된 2상 열전달 특성을 보고하고 2상 열전달에 대한 마이크로 및 나노 규모의 표면 특성 효과를 보여줌으로써 비등 열 전달을 효과적으로 향상시키는 새로운 통찰력을 제공합니다. .

Study on microbubble dynamic behaviors at vertical micro-nano hybrid surfaces based on open capillary microgrooves heat sink

More Enhancing Boiling Heat sentences
More Sentences

Boiling Heat sentence examples within Enhance Boiling Heat

Enhance Boiling Heat

For example, surface modification by nanocoatings has been shown to efficiently enhance boiling heat transfer.

nan

Molecular dynamics simulations of thin-film evaporation: The influence of interfacial thermal resistance on a graphene-coated heated silicon substrate

Enhance Boiling Heat

Here, a graphene-coated micropillar structure (GMS) is proposed in order to enhance boiling heat transfer by suppressing vapor film formation on the surface.

여기에서는 표면의 증기막 형성을 억제하여 비등 열전달을 향상시키기 위해 그래핀이 코팅된 미세기둥 구조(GMS)를 제안하였다.

Enhanced nucleate boiling using a reduced graphene oxide-coated micropillar

More Enhance Boiling Heat sentences
More Sentences

Boiling Heat sentence examples within Enhanced Boiling Heat

Enhanced Boiling Heat
강화된 끓는 열

The research results can be guided for further studying the mechanism of electric field enhanced boiling heat transfer.

연구 결과는 전기장 강화 비등 열 전달 메커니즘을 추가로 연구하는 데 지침이 될 수 있습니다.

Research on dynamic behavior of bubble under the action of electric field

Enhanced Boiling Heat
강화된 끓는 열

Surface coating is considered as a common approach for achieving an enhanced boiling heat transfer.

표면 코팅은 향상된 비등 열 전달을 달성하기 위한 일반적인 접근 방식으로 간주됩니다.

Experimental study of nucleate pool boiling heat transfer improvement utilizing micro/nanoparticles porous coating on copper surfaces

More Enhanced Boiling Heat sentences
강화된 끓는 열 More Sentences

Boiling Heat sentence examples within Convective Boiling Heat

Convective Boiling Heat
대류 끓는 열

An experimental investigation was performed on the convective boiling heat transfer of the annular flow in concentric and eccentric annuli with a central heating rod in an unheated tube.

실험적 조사는 가열되지 않은 튜브의 중앙 가열 막대가 있는 동심 및 편심 고리의 고리 흐름의 대류 비등 열 전달에 대해 수행되었습니다.

Experimental investigation of the annular flow caused by convective boiling in a heated annular channel

Convective Boiling Heat
대류 끓는 열

In this work, we show that during convective boiling heat transfer, the vapor Reynolds number plays a dominant role which has been overlooked.

이 연구에서 우리는 대류 비등 열 전달 동안 증기 레이놀즈 수가 간과되었던 지배적인 역할을 한다는 것을 보여줍니다.

On the scaling of convective boiling heat transfer coefficient

More Convective Boiling Heat sentences
대류 끓는 열 More Sentences

Boiling Heat sentence examples within Fed Boiling Heat

Fed Boiling Heat

The current study experimentally characterizes the capillary-fed boiling heat transfer behavior in such a two-layer evaporator wick, compared to a homogeneous (single-layer) wick, over a 1 cm2 evaporator area.

현재 연구는 1cm2 증발기 영역에서 균질(단일층) 심지에 비해 이러한 2층 증발기 심지의 모세관 공급 비등 열 전달 거동을 실험적으로 특성화했습니다.

Experimental investigation of boiling regimes in a capillary-fed two-layer evaporator wick

Fed Boiling Heat

This two-layer structure decouples the functions of liquid resupply (cap layer) and capillary-fed boiling heat transfer (base layer), making the design scalable to heat input areas of ~1 cm2 for operation at 1 kW/cm2.

이 2층 구조는 액체 재공급(캡 층)과 모세관 공급 비등 열 전달(기재 층)의 기능을 분리하여 1kW/cm2에서 작동하기 위해 ~1cm2의 열 입력 영역으로 설계를 확장할 수 있습니다.

Design of an Area-Scalable Two-Layer Evaporator Wick for High-Heat-Flux Vapor Chambers

More Fed Boiling Heat sentences
More Sentences

Boiling Heat sentence examples within Wall Boiling Heat

Wall Boiling Heat

Two case studies based on the proposed approach are performed, focusing on two-phase flow dynamics and on wall boiling heat transfer, respectively.

제안된 접근 방식을 기반으로 하는 두 가지 사례 연구가 각각 2상 유동 역학과 벽 비등 열 전달에 중점을 두고 수행되었습니다.

Uncertainty quantification of two-phase flow and boiling heat transfer simulations through a data-driven modular Bayesian approach

Wall Boiling Heat

Therefore, the two-fluid wall-boiling model developed based on the characteristic of small-scale nucleate bubbles might not be sufficient for prediction of wall boiling heat transfer on a downward facing heating surface.

따라서 소규모 핵 기포의 특성을 기반으로 개발된 2유체 벽 비등 모델은 아래쪽을 향한 가열 표면의 벽 비등 열 전달 예측에 충분하지 않을 수 있습니다.

Modeling and simulation of flow boiling heat transfer on a downward-facing heating wall in the presence of vapor slugs

More Wall Boiling Heat sentences
More Sentences

Boiling Heat sentence examples within boiling heat transfer

boiling heat transfer
끓는 열전달

Enhancing boiling heat transfer by surface modification has the potential to increase the efficiency of energy systems and to address thermal management bottlenecks in electronics.

표면 개질을 통해 끓는 열 전달을 향상시키면 에너지 시스템의 효율성을 높이고 전자 장치의 열 관리 병목 현상을 해결할 수 있습니다.

Composite porous surfaces of microcavities for enhancing boiling heat transfer

boiling heat transfer
끓는 열전달

2 improve average boiling heat transfer coefficient by 58% and 86% and reduce wall superheat at ONB by 4.

2 평균 비등 열 전달 계수를 58% 및 86% 향상시키고 ONB에서 벽 과열도를 4로 줄입니다.

On the effect of silver nanoparticles deposition on porous copper foams on pool boiling heat transfer enhancement: an experimental visualization

More boiling heat transfer sentences
끓는 열전달 More Sentences

Boiling Heat sentence examples within boiling heat flux

boiling heat flux
끓는 열유속

The new correlation which adequately predicts the local variation of the nucleate boiling heat flux along the outer surface of the RPV under IVR-ERVC conditions can be used to describe the long-term cooling behavior of the corium within the RPV of advanced nuclear power plants.

IVR-ERVC 조건에서 RPV의 외부 표면을 따라 핵 끓는 열유속의 국부적 변화를 적절하게 예측하는 새로운 상관 관계는 고급 원자력 발전소의 RPV 내에서 노심의 장기 냉각 거동을 설명하는 데 사용할 수 있습니다.

Development of a downward-facing nucleate boiling correlation for thermal hydraulics analysis

boiling heat flux
끓는 열유속

All of these replacement refrigerants had measured boiling heat fluxes that were larger than that for R123 for most heat fluxes.

이 모든 대체 냉매는 대부분의 열유속에 대해 R123보다 더 큰 끓는 열유속을 측정했습니다.

Pool Boiling of R514A, R1224 yd(Z), and R1336mzz(E) on a Reentrant Cavity Surface

More boiling heat flux sentences
끓는 열유속 More Sentences

Boiling Heat sentence examples within boiling heat sink

boiling heat sink

There exist some problems such as flow instability and critical heat flux (CHF) caused by the local dryout phenomenon, which is an obstacle to the application of microchannel flow boiling heat sink.

Numerical Investigation on Bubble Growth and Merger in Microchannel Flow Boiling With Self-Rewetting Fluid

boiling heat sink

The major role of designs of flow boiling heat sinks is to mitigate or delay these instabilities to reach stable and high performance cooling from heat transfer and pressure drop point of views.

A Review: New Designs of Heat Sinks for Flow Boiling Cooling

More boiling heat sink sentences
More Sentences

More Boiling Heat 끓는 열 sentence examples
10.1080/08916152.2021.1873876

The boiling heat-transfer performances of R1234ze(E)/R152a (0.

R1234ze(E)/R152a의 끓는 열전달 성능(0.

Flow boiling heat transfer performances of R1234ze(E)/R152a in a horizontal micro-fin tube

More Boiling Heat 끓는 열 sentence examples
10.1088/1742-6596/1378/3/032065

80 during the pre-boiling heating process indicates that the cooker can be recommended for sterilization.

예열 가열 과정에서 80은 밥솥을 살균 권장할 수 있음을 나타냅니다.

Thermal Analysis of Solar Box Cooker in Omu-Aran Metropolis

More Boiling Heat 끓는 열 sentence examples
10.1016/J.IJHEATMASSTRANSFER.2019.118554

When the annular spacing decreases, heat transfer deterioration will worsen accompanied with a sudden drop in boiling heat-transfer coefficient.

환형 간격이 감소하면 비등 열전달 계수의 급격한 저하와 함께 열전달 열화가 악화됩니다.

Flow boiling in horizontal annuli outside horizontal smooth, herringbone and three-dimensional enhanced tubes

More Boiling Heat 끓는 열 sentence examples
10.1016/J.IJMULTIPHASEFLOW.2018.11.017

The results appear to fit all relevant data for film-boiling heat-transfer coefficient within an error of 15%.

결과는 15%의 오차 내에서 필름 끓는 열전달 계수에 대한 모든 관련 데이터에 맞는 것으로 보입니다.

Inclined film boiling: Film stability and heat transfer

Learn more from Boiling Heat 끓는 열

Boiling Heat 끓는 열

Boiling Heat 끓는 열
Encyclopedia 백과사전

Boiling Heat(끓는 열)란 무엇입니까?

Boiling Heat 끓는 열 - The boiling heat-transfer performances of R1234ze(E)/R152a (0. [1] 80 during the pre-boiling heating process indicates that the cooker can be recommended for sterilization. [2] When the annular spacing decreases, heat transfer deterioration will worsen accompanied with a sudden drop in boiling heat-transfer coefficient. [3] The results appear to fit all relevant data for film-boiling heat-transfer coefficient within an error of 15%. [4]
R1234ze(E)/R152a의 끓는 열전달 성능(0. [1] 예열 가열 과정에서 80은 밥솥을 살균 권장할 수 있음을 나타냅니다. [2] 환형 간격이 감소하면 비등 열전달 계수의 급격한 저하와 함께 열전달 열화가 악화됩니다. [3] 결과는 15%의 오차 내에서 필름 끓는 열전달 계수에 대한 모든 관련 데이터에 맞는 것으로 보입니다. [4]

critical heat flux 임계 열유속

These saturated pool boiling experiments and the visualizations verify that the present two-phase immersion cooling can enhance both the boiling heat transfer and the critical heat flux of water and FC-72. [1] As a result, the NaCl solution presents a lower nucleate boiling heat flux than that of water when the imposed superheat is smaller than a critical superheat, while it exhibits a larger heat flux even a higher critical heat flux than water when the superheat is higher than the critical superheat. [2] Critical heat flux (CHF) is an important heat transfer deterioration phenomenon during boiling heat transfer. [3] Understanding nucleate pool boiling heat transfer and, in particular the accurate prediction of conditions that can lead to critical heat flux, is of the utmost importance in many industries. [4] Boiling heat transfer performance, including critical heat flux (CHF), heat transfer coefficients (HTCs), and the onset of nucleate boiling (ONB), are investigated. [5] Despite contradiction in nucleate pool boiling heat transfer coefficient of nanofluids, the enhancement in critical heat flux (CHF) has been widely approved. [6] The saturation temperature of only 34 °C at atmospheric pressure, the high boiling figure-of-merit (BFOM), Critical Heat Flux (CHF) and maximum nucleate boiling heat transfer coefficient (hMNB) make HFE-7000 dielectric liquid a good choice for immersion cooling applications. [7]