Adhesion Improvement(접착력 향상)란 무엇입니까?
Adhesion Improvement 접착력 향상 - The improvement of the SC of the acid-treated substrate was contributed to the adhesion improvement between a current collector and an electrode material, and the hydrophilicity improvement, resulting in a large amount of electrolyte ions accessing into the electrode materials and subsequently enhancement of their capacitive characteristics. [1] Also, adhesion improvement between the WF via enhanced wood fibers wetting with maleated PLA was employed. [2] The average coefficient of friction was almost similar for all pads and wear performance was excellent for SS316 and SS304 based brake-pads since these materials had higher surface energy vis-a-vis the adhesion improvement with the matrix. [3] Techniques for vacuum UV (VUV) photo-oxidation of materials, using emission from plasmas with wavelengths shorter than 180 nm, are reviewed focusing on adhesion improvement for polymers, such as, fluoropolymers, membranes used in fuel cells, polyimides, polyethylene, and polystyrene. [4] This enhancement may be associated with the structure refinement, grain boundary purification, and adhesion improvement of the Al2O3 oxide scale on the coating surface. [5] The corrosion resistance of DLC films with Cr interlayer for adhesion improvement was studied. [6] The interface interaction was moreover activated using finely ground concrete recyclate, whose individual grains (1−64 μm) ensure an adhesion improvement in interfacial zones. [7] Additionally thin buffer zones using atomic layer deposition (ALD) are investigated for adhesion improvement. [8] The adhesion improvement of a modified tin surface was also confirmed by a simple cross-cut tape peeling test. [9] Nanoscratch tests, complemented by scanning electron microscopy and energy-dispersive X-ray spectroscopy, were used to evaluate the critical load for delamination to certify and quantify the adhesion improvement. [10] The role of the Ti –sublayer on a sintered powder tungsten carbide substrate is not only limited by the adhesion improvement, but it is mainly used to neutralise the grain boundary microcracks on a surface. [11]산처리된 기판의 SC 향상은 집전체와 전극물질의 접착력 향상 및 친수성 향상에 기여하여 많은 양의 전해질 이온이 전극물질에 접근하여 용량성 향상에 기여하였다. 형질. [1] 또한, 말레화 PLA로 강화된 목섬유 습윤을 통해 WF 사이의 접착력 향상이 사용되었습니다. [2] 평균 마찰 계수는 모든 패드에서 거의 유사했으며 SS316 및 SS304 기반 브레이크 패드는 매트릭스와의 접착력 향상에 비해 표면 에너지가 더 높기 때문에 마모 성능이 우수했습니다. [3] 180 nm 미만의 파장을 갖는 플라즈마의 방출을 이용한 재료의 진공 UV(VUV) 광산화 기술은 플루오로폴리머, 연료전지에 사용되는 멤브레인, 폴리이미드, 폴리에틸렌, 폴리스티렌과 같은 고분자의 접착력 향상을 중심으로 검토됩니다. . [4] 이러한 향상은 구조 미세화, 입계 정화 및 코팅 표면의 Al2O3 산화물 스케일의 접착력 향상과 관련이 있을 수 있습니다. [5] 접착력 향상을 위해 Cr 중간층을 갖는 DLC 필름의 내식성을 연구했습니다. [6] 또한 개별 입자(1-64μm)가 계면 영역에서 접착력 향상을 보장하는 미세하게 분쇄된 콘크리트 재생재를 사용하여 계면 상호 작용이 활성화되었습니다. [7] 또한 ALD(Atomic Layer Deposition)를 사용하는 얇은 버퍼 영역은 접착력 향상을 위해 조사됩니다. [8] 개질된 주석 표면의 접착력 향상은 또한 간단한 크로스 컷 테이프 박리 테스트에 의해 확인되었습니다. [9] 주사 전자 현미경 및 에너지 분산 X선 분광법으로 보완된 나노 스크래치 테스트를 사용하여 접착 개선을 인증하고 정량화하기 위해 박리에 대한 임계 하중을 평가했습니다. [10] 소결 분말 텅스텐 카바이드 기판에서 Ti-하위층의 역할은 접착력 향상에 의해 제한될 뿐만 아니라 주로 표면의 입계 미세 균열을 중화하는 데 사용됩니다. [11]
Significant Adhesion Improvement 상당한 접착력 향상
The most significant adhesion improvement of the PEG modified LDPE surface was achieved using 10. [1] The most significant adhesion improvement of the PEG modified LDPE surface was achieved using 10. [2]PEG 변형 LDPE 표면의 가장 중요한 접착 개선은 10을 사용하여 달성되었습니다. [1] PEG 변형 LDPE 표면의 가장 중요한 접착 개선은 10을 사용하여 달성되었습니다. [2]